Services : Silt Extractor : Specification
Clear WW
Pump House Components
Main wash motor:
415 volt 3 –phase 22Kw (Star-Delta Starter)
Main wash pump:
3 inch PN16 3600 rpm cen
Recovery pump motor:
415 volt 3 phase 4Kw
Recovery pump:
3 inch PN16 360rpm self-priming
Air Compressor:
1.5hp 24 litres 1 phase 1.1Kw
Hand Lance Motor:
230 volt 1 phase 2.2 Kw
Hand Lance Pump:
100 bar 12 Litres/min
Hand Lance Operating Button:
External
Fan Heater (Thermostat Controlled:
230 volt 1 phase 2Kw
Main Isolator:
125 amp
- 2 Pneumatic changeover valves
- Engine control box and monitoring system
- External emergency stop button
- Chemical (COAGULANT) Peristaltic Dosing pump 230 volt 1 phase 3.5w
Electrical Supply
- A 415v 3 phase 100A supply is required
- Based on the information above we would recommend a 25mm2 4 core SWA cable with a neutral and separate earth (16mm2)
- A 2m length of this above ground will be sufficient for the connections to be made
Please note: Electrical equipment must be installed and wired to Mines and Quarry Regulations.
Water Supply
For topping up the water reclamation tank and use of a hand lance (optional) we recommend a mains water supply terminated
in a 3/4 inch male BSP fitting with isolator.
Wesley Services (Leeds) Ltd reserve the right to change the above specification and design without notice.
Water Recycling Tank
Capacity:
150,000 litres (3,500 litres clean)
Length:
6.54 metres without silt chute
7.36 with silt chute
Width:
2.2 metres
Height:
2.26 metres without silt chute
2.95 metres with silt chute
Weight:
4,500 kilos
Fitted with:
3” outlet connector for wash nozzles
3” outlet connector for washdown nozzles
3” inlet connector for sump pump connection
2x6” bauer connectors
2x6” butter valves
1 ¾” ball valve
Scrapper Motor 415 volt 3 phase 0.09Kw
6 x 1295mm long silt scrapper blades scrapping speed of 1m/min
Conveyor chain waterproof and made from high tensile steel
6 x Lamella pods with a 27.5m2 surface area.
Sump Tank
Capacity:
1000 litres
Width:
1 metre
Length:
1 metre
Height:
1.325 metres
Fitted with:
3” Electrical submersible pump Debris collecting basket Security Lid
Noise level: dB at 1.6m high and 1m distance from, and at various points around, the water recycling tank and pump house.
Clear 85
Water Recycling Tank
Capacity:
14,500 litres total
Length:
7.36 m (6.54 metres with silt chute removed)
Width:
1.62 m frame (2.2 m metres at its widest point)
Height:
3.45m (2.76 metres with silt chute removed)
Weight:
300 Kg
Fitted with:
3” inlet connector for sump pump connection
2x6” bauer connectors
1 x 6” butterfly valves
16 amp main isolator
415 volt 3 phase 0.12Kw Silt Extraction Scrapper motor
6 x 1295mm silt Scraper blades with a scraping speed of 1m/min. The conveyor chain waterproof and made from high tensile steel.
6 x 27.5 m2 pods Lamella Pods
External Emergency Stop Button
Optional:
Chemical (FLOCCULENT/COAGULANT) peristaltic
dosing pump 230 volt 1 phase 3.5w
Floating debris collection system
A7 Finish:
Zinc phosphate primer
Zinc phosphate QD semi gloss green – RAL 6001
Electrical supply:
A 415v 3 phase 16A supply is required
Based on the information above we would recommend a 25mm2 4 core SWA cable with a neutral and separate earth (16mm2).
A 2m length of this above ground will be sufficient for the connections to be made.
Please note: Electrical equipment must be installed and wired to Mines and Quarry Regulations.
Wesley Services (Leeds) Ltd reserve the right to change the above specification and design without notice.
